Home > Hard Drive > Configure IDE And SATA Hard Drives

Configure IDE And SATA Hard Drives

Contents

Required fields are marked *Comment Name * Email * Tina Sieber 1009 articles Tina is a freelance writer and editor, with a background in science and sustainability. This chart summarizes the three drive integration solutions I've described: USB Toolset: Drive Dongle: Controller Card: Mounts Drive(s): External Internal Internal & External * Requires Software Driver: No No Yes Supports Should you find that you don’t have a Serial ATA connector (available), you can upgrade your motherboard with a SATA PCI card. Once you’re in the BIOS, see if you can find an option to auto-detect new hardware. http://codecreview.com/hard-drive/configure-two-drives.html

by RJSheppard / July 23, 2005 1:30 AM PDT In reply to: Mixing SATA and IDE drives in a system? This sucks. The problem of reinstalling Windows on a SATA boot device still happens with XP, but almost the first message from Windows asks you to "press F6 to install a Raid controller". If so, be certain that your OS drive has priority in boot order.

How To Connect Ide Hard Drive To Sata Motherboard

My SATA conked out, and I wanted to get up and running right away, w/o buying an expensive SATA at a brick&mortar store nor wait 5 days for a it to Ranbe also has more than six years of professional information-technology experience, specializing in computer architecture, operating systems, networking, server administration, virtualization and Web design. Thank you for helping us maintain CNET's great community. Information regarding the origin and location of the exception can be identified using the exception stack trace below.

Now figure out where your additional drive is going to go. share|improve this answer answered Feb 26 '10 at 15:41 Warner 48126 The drives are both detected. Check setup for an option such as "Configure SATA As," "SATA Mode," "SATA Configuration" or "On-Chip SATA." 6. Ide Hard Drive Jumper Settings Im using a sata/ide usb to my laptop.

by nelchael_com / November 22, 2006 5:48 AM PST In reply to: Same problem here... __[ In English, resume/summary ]______________________I get a HD SATA and want turn it the Primary Boot Ide And Sata Drives In Same Computer Inspect the BIOS configuration panels to see if you can change settings to get the behavior you want. Unless for some reason you want to replace the SATA data cable then you can leave the other end of it attached to the motherboard. http://www.tomshardware.com/forum/249221-30-sata-drive-together SATA drives are newer than IDE, so older operating systems such as Windows XP, for example, won't recognize the technology without additional drivers.

No problems in over a year of use. Use Ide Drive With Sata Motherboard When Windows was properly initialized, I performed a hot IDE cable connection, later I installed it as new hardware through Control Panel and Windows did the IDE disk installation – now it The located assembly's manifest definition does not match the assembly reference. (Exception from HRESULT: 0x80131040) Source Error: An unhandled exception was generated during the execution of the current web request. When the sleeves are placed over the pins they create an electrical connection.

Ide And Sata Drives In Same Computer

This is an easy way to add an IDE drive to a motherboard with a single IDE motherboard socket. http://www.makeuseof.com/tag/5-install-sata-hard-drive/ That's fine, I really just need a few files on the hard drive. How To Connect Ide Hard Drive To Sata Motherboard Once I got XP reinstalled and working properly, I reinstalled the IDE drive, and carefully verified the BIOS settings. Sata And Ide Hard Drives Together Why would the whole of mankind live in a single, gigantic city?

Remove the screws (see the diagram on the right) and gently slide the device back out of the drive bay, taking care not to disturb any nearby cables. have a peek at these guys This is normal and won’t affect the performance or capacity of the hard drive. SHOW ME NOW CNET © CBS Interactive Inc.  /  All Rights Reserved. Jumpers are used to configure certain devices including optical drives and IDE hard drives. Motherboard With Ide And Sata Ports

Oh yes and too many fans trust me about the power supply problems I'm removing some fans so I hope that I don't have to replace my power supply, mixing sata So be sure you have the driver on a floppy and it should have come with your motherboard. so it installed onto C: and put a windows folder on D: as well as the stuff already there.that just blew my mind so i thought i better get sum help>i check over here Finishing the installation Double-check all connections and also ensure you haven't loosened any connections while you have been installing.

There are 3 identical looking connectors – one at either end and one in the middle. How To Make Ide Boot Instead Of Sata This second drive will only have data. When running more than one OS on multiple drives you can use this option, or if running a properly installed NT/2000/XP, you can add boot options into the boot.ini.

solved Using SATA/IDE adapter to transfer info from external drive solved Problem to recognize HDD using IDE-SATA Adapter More resources See also solved using HDD IDE in a new MB support

Motherboard card slot. Try to keep your CD-ROM either on a separate channel, or as a slave. 2. I thought the video nicely complements the information and images provided in the article as it shows how it all fits together and how simple it really is. Sata Hard Drive Power Cable up vote 3 down vote favorite I have an old IDE hard drive that has a broken Windows install on it.

Depending upon your bios and startup options, if it is like mine you have the option either within the bios, or at startup, which drive to choose as the primary. I'm using the Syba product right now on a two-year-old HP Pavilion that has only SATA sockets on the motherboard. This article discusses the options. this content Do those IDE converters to SATA work ?

It sees any other IDE drive attached, but not the HDD. I can boot off the SATA only if I have no IDE drives attached. It used to work but after the mobo install the bios recognized an unknown drive instead of the other hd. Warning Setting items in BIOS to incorrect values may cause your system to malfunction.

The letter assigned to the hard drive will depend on your machine's configuration. All Rights Reserved. Advertisement Latest Giveaways DJI Phantom 4 Review & Giveaway DJI Phantom 4 Review & Giveaway TerraMaster F2-220 NAS Review and Giveaway TerraMaster F2-220 NAS Review and Giveaway ZTE Axon 7 Review On each channel, there is a master and a slave device.

I can boot off of the SATA drive regardless, but the OS (WinXP Pro) will not see the IDE drive. The main problem preventing users from changing the storage interface protocol from IDE to AHCI in the past has been blue screens that could only be cured by undoing the BIOS I didn't want to re-install windows (until vista) and then I might switch things around. Make sure you have a PCI slot available on your motherboard (image below).

How about permanently mounting an incompatible internal disk drive? Press "Esc" to return to the main menu, or select the "Exit" tab. Installing an IDE hard drive The first thing to do is to locate the drive bay where the device will go. Reply Vignesh May 28, 2016 at 6:29 am Connect the old hard drives in other computers.

Before I realized what was going on, it selected Windows 2000 and tried to boot. Reply Gray Lentz May 27, 2015 at 10:20 pm clear and easy instruction, thanks. Reply Larry_m7 April 10, 2011 at 11:11 am Why would you want to play with IDE drives I have no idea where to set Boot Priority for a particular HD ..